Celsius W370 status codes

Moderator: ModTeam

SimpleMatters
Posts: 1
Joined: Thu Sep 27, 2012 5:05
Product(s): Celsius W370

Celsius W370 status codes

Postby SimpleMatters » Thu Sep 27, 2012 13:08

Hi.

My Celsius W370 with D2831-S mainboard freezes on startup. Front LED indicator shows STATUS 90, display stucks at POST screen and remains there for indefinite time. Subsequent reboots can finally overcome this problem in about 10-20 minutes and start the OS. I strongly suspect problems with power, but can't confirm it since I don't know what STATUS 90 means. Can anyone give me a hint on status or error codes for this mainboard?

Thanks.

User avatar
sabrex
Posts: 1145
Joined: Thu Jun 05, 2003 0:01
Product(s): Various
Location: England
Contact:

Re: Celsius W370 status codes

Postby sabrex » Thu Sep 27, 2012 15:51

BIOS POST-Codes (Port 80 status indicators)
BIOS-POST codes are visible on the LCD-display (connected to the LCD-connector) or onboard via 8 yellow LEDs (L0-L7, L0 is the lowest bit, L7 the highest).

01h
Initialize IPMI
02h
Verify Real Mode
03h
Disable non-maskable interrupt(NMI)
04h
Get CPU type
06h
Initialize system hardware
07h
Pre-Init chipset (Shadow-Register)
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST values
12h
Restore CPU control word during warm boot
13h
Initialize PCI bus mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
BIOS ROM checksum
17h
Initialize cache before memory autosize
18h
Initialize 8254 timer
1Ah
Initialize 8237 DMA controller
1Ch
Reset programmable interrupt controller
20h
1-3-1-3
Test DRAM refresh
22h
Test 8742 keyboard controller
24h
Set segment register ES to 4GB access
26h
Enable A20 line
28h
1-3-3-1
Autosize DRAM
29h
Initialize POST memory manager
2Ah
Clear 512KB base RAM
2Bh
Initialize CMOS emulation.
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of memory bus
2Fh
Enable cache before system BIOS shadow

30h
1-4-1-1
RAM failure on data bits xxxx of high byte of memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix dispatch manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Bh
Initialize debug services
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
41h
Initialize RomPilot support
42h
Initialize interrupt vectors
45h
POST device initialization
46h
2-1-2-3
Check ROM copyright notice
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in the system
4Bh
Start quiet boot
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
4Fh
Pre-Initialize boot sequence
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
55h
USB initialization
57h
Initialize 1394 devices
58h
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt "Press F2 to Enter Setup"
5Bh
Disable CPU cache
5Ch
Test RAM between 512KB and 640KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to user patch 1
66h
Configure advanced cache registers
67h
Initialize multi processor APIC
68h
Enable external and CPU cache
69h
Setup system management mode(SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Setup hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCE IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure motherboard configurable devices(MCD)
88h
Initialize BIOS data area(BDA)
89h
Enable non-maskable interrupt(NMI)
8Ah
Initialize extended BIOS data area(EBDA)
8Bh
Test and initialize PS/2 mouse

8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives
90h
Initialize hard disk controllers

91h
Initialize local bus hard disk controllers
92h
Jump to user patch 2
93h
Build MP table for multi processor boards
95h
Install CD ROM for boot
96h
Set segment register ES to 64KB access
97h
Fixup multi processor table
98h
1-2
Search for option ROMs(Beeps on checksum errors)
99h
Check for SMART drive
9Ah
Shadow option ROMs
9Ch
Setup power management
9Dh
Initialize security engine
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter Setup
AEh
Clear boot flag
B0h
Check for errors
B1h
Unload RomPilot support
B2h
Prepare to boot operating system(POST done)
B3h
Store CMOS emulation values to non-volatile area.
B4h
1
One short beep before boot
B5h
Terminate quiet boot
B6h
Check password
B7h
ACPI support
B9h
Prepare boot
BAh
Initialize DMI parameters
BBh
Initialize PnP option ROMs
BCh
Clear parity checkers
BDh
Display multi boot menu
BEh
Clear screen
BFh
Check virus and backup reminders
C0h
Try to boot with INT19h
C1h
Initialize POST error manager
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnP and dual CMOS
C6h
Initialize note dock
C7h
Initialize note dock late
C8h
Force check
C9h
Extended checksum
CAh
Serial Keyboard Support
CCh
Serial Video Support
CDh
PCM ATA Check
D1h
Initialize BIOS stack and various working buffer
D2h
Unknown interrupt
D3h
Initialize Memory Reporting interface.
D4h
Determine CPU brand
D6h
Initialize PCCards (CardBus,...)
D7h
FirstWare support
D8h
Initialize ASF
D9h
Initialize IPMI, 2nd part

DAh
Pre-Initialize PCIe devices
DBh
FirstWare support, 2nd part
DCh
Verify microcode update
DDh
Initialize remote flash support
DEh
Initilize PXE UNDI code
DFh
FSC specific initialization routines
E0h
(U)EFI: Initialize non-volatile RAM.

please disconnect tiny LCD. If then the system boots Ok could be that - latest bios should rectify
Please make sure your bios is not on 6.00.1.02
If it is update bios to latest 6.00.1.19

Bobi123
Posts: 1
Joined: Sun Dec 30, 2012 14:45
Product(s): W370, MB: D2817

Re: Celsius W370 status codes

Postby Bobi123 » Mon Dec 31, 2012 13:35

What to do if BIOS version: 6.00.1.19 (the latest) and the same problem with status:90 on my Celsius W370?
After a couple of minutes you can start PC again.
Istn't it related with power supply to disk controller?


Return to “CELSIUS Workstations”

Who is online

Users browsing this forum: No registered users and 2 guests