Primergy TX150 S7 RAM Replacement

PRIMERGY, SPARC Enterprise Server, PRIMEFLEX, PRIMEPower, BS2000

Moderator: ModTeam

tiThink
Posts: 2
Joined: Tue Feb 02, 2021 12:42
Product(s): Primary TX150 S7

Primergy TX150 S7 RAM Replacement

Postby tiThink » Tue Feb 02, 2021 13:58

Hello,
I am trying to increase the RAM memory of my server but I find that the module that I have acquired is not enough, they are 4GB DDR3 10600R 1333Mhz ECC. It does not work, in the coloured slots it gives me the beep code 1-3-3-1(Automatic DRAM size) and in the black slot it does not give me an image, it currently has a 4GB DDR3l 128000R 1600Mhz ECC and it works in the black slot. How can I find out that the slots are not in a bad state? How should I put the memory?

Regards.

User avatar
Ask Fujitsu
Moderator
Posts: 724
Joined: Fri Aug 02, 2019 10:02
Product(s): n/a
Contact:

Re: Primergy TX150 S7 RAM Replacement

Postby Ask Fujitsu » Wed Feb 03, 2021 12:51

Hello :)

First of all, please check the attached document.
On page 11, there is information on which memory modules (part numbers) can be used in this server and which modules can be mixed or not.

In addition, please check this document:
https://support.ts.fujitsu.com/IndexDow ... 8C949437F1
In section 5.1 you can find necessary information about how to populate memory modules.

Thank you,
Ask Fujitsu Team
Attachments
cnfgTX150S7.pdf
(483.57 KiB) Downloaded 260 times

tiThink
Posts: 2
Joined: Tue Feb 02, 2021 12:42
Product(s): Primary TX150 S7

Re: Primergy TX150 S7 RAM Replacement

Postby tiThink » Tue Mar 02, 2021 13:42

Hello, after consulting the manual I am still in the same condition.

I have tried 3 memory modules
DDR3 4 GB 2Rx4 PC3-10600R from HP
DDR3 4 GB 1Rx4 PC3-10600R from Samsung
DDR3l 4GB 1Rx4 PC3l-12800R from Micron
in the main slot 1A, all have given me the same problem black screen and no image, I have looked at the bios and can not configure anything.
But with the one I currently have which is a
DDR3l 4GB 2Rx4 PC3l-12800R from Samsung works perfectly.

Regards.

User avatar
Ask Fujitsu
Moderator
Posts: 724
Joined: Fri Aug 02, 2019 10:02
Product(s): n/a
Contact:

Re: Primergy TX150 S7 RAM Replacement

Postby Ask Fujitsu » Mon Mar 08, 2021 15:37

Hello :)

First of all, please check this document: https://sp.ts.fujitsu.com/dmsp/Publicat ... X150S7.pdf. On page 11, there is a piece of information on which memory modules (part numbers) can be used in this server and which modules can be mixed or not.

In addition, please check this document:
https://support.ts.fujitsu.com/IndexDow ... 8C949437F1. In section 5.1 you can find necessary information about how to populate memory modules.


Please read this document:
https://www.fujitsu.com/downloads/KR/se ... 30_Oct.pdf
https://sp.ts.fujitsu.com/dmsp/Publicat ... X150S7.pdf. On page 11, there is a piece of information on which memory modules (part numbers) can be used in this server and which modules can be mixed or not.

Thank you,
Fujitsu Forum


Return to “Server Products”

Who is online

Users browsing this forum: No registered users and 1 guest