Hello Nicola

I think you're missing the Front USB/VGA Breakout Cable
This cable consists out of a VGA connector and 2 USB connectors it enables you to connect your USB CD-ROM drive to the server.

Regards.
Data.

Hello Damian. I'm afraid that these caddies can not be ordered seperately from the HDD. Normally the caddies should be delivered with the disks when you buy them from FSC to ensure that you have official supported disks. Anyway you could try to contact the FSC helpdesk and ask for the spares departm...

Hello acheron.

Seems to me like a HW malfunction.
I would contact FSC for a service intervention.

Regards.
data.

Hi Cristaki

First of all you should enable USB legacy support in your servers BIOS.
Next to that you need to change some settings in your RSB card.
Unfortunately I'm not sure which settings anymore.
Try the FSC helpdesk, they should now.

Regards.
Data.

I think ServerStart isn't downloadable but you could try: http://www.fujitsu-siemens.com/serverstart or http://download.fujitsu-siemens.com/server/serverstart/en/default_alt.htm I did also find the following link for the support cd's: ftp://ftp.fujitsu-siemens.com/fsc/supportcds Good luck. Data.

Hi Salih-ro. When installing a TX200 with host raid you should first create a RAID set with the build in tool (CTRL - A). After that you should apply the correct hostraid driver via the F6 option. a320raid.sys version:1.02.074 See also the released drivers.xls: http://support.fujitsu-siemens.com/dow...

Hello Meldmeaan.

You are right, it is not possible to create a RAID 5 with a LSI SAS 1068 -2107 IME controller.
If you want you could update your server with a SAS Zero Channel Raid controller.

Regards.
Data.

Hi bytekbjorn. The (IERR#), Assertion message is an IPMI (Intelligent Platform Management Interface) related signal which means that there is a serious processor error. I did find some info on the following site: http://www.compactpci-systems.com/columns/spec_corner/pdfs/11.2002.pdf You also could h...

Hi ifinisterre The RX100 S3 has a LSI SATA RAID controller according to my knowledge. The management tool for this controller is GAM (Global Array Manager) and can be found on the server start CD which is delivered with the system. The online version of serverstart can be found on the following URL ...

Hi Sschocke. It seems to me that you start from the wrong SerSt CD. You always NEED to start with SerSt CD 1. When installing a x64 OS you will be asked to put in the second SerSt CD (2) later on Make sure to use a Serverstart status diskette when installing a x64 OS. When installing a x32 bit os yo...

Hi Kay1

Seems that you've created a dedicated hot-spare.
Make sure to create a Global Hot spare instead.

Greetings
Data

Hi Elizabetass.

Best way is to get in contact with FSC support. I'm sure they can help you.

Greetings.
Data.

Hi Leon. I think you can use the Serverview agents in a Netware 6.0 environment. The serverview application can then be installed on a Windows management station. The serverview application and agents can be found on: http://www.fujitsu-siemens.com/serversupport In the info section you'll find some ...

Hi leonsmit. Basically every piece of hardware is temperature dependent. I've just looked up the data sheet and according to this the ambient temperature should not exceed 35 degrees Celsius. Some tips: Have you installed serverview. Does it say anything about the temperature of you server? Can you ...

Hi Joeh

Try installing with serverstart in expert mode.
During the serverstart install (for W2K3) you should (although not supported) be able to select Winxp.


Regards.
Data.